We share the latest product reviews of Under Cabinet TVs, Under Cabinet CDs, Under Cabinet Accessories. Please visit our STORE to get more product information, or check our hand-pick best sellers of those products for you! Also check our tips session to get more tips or experience from other users.
I am thinking about buying one and was wonder if they are easy to install and then remove.. We will be moving in six months and don’t want to buy it if we can’t take it with us…
Thanks…
Under the kitchen cabinet cd unit Are they easy to install? Can you remove it easily?
I am thinking about buying one and was wonder if they are easy to install and then remove.. We will be moving in six months and don’t want to buy it if we can’t take it with us…
Thanks…
Its came with two screws and two green plastic things. I am not sure what those are for. What do I do with them?
There are 2 quarter inch holes in the back and 4 quarter inch holes on the bottom of the safe. The thickness of the cabinet sides are about 3/4 inch thick. I don’t have access to the back or bottom of the cabinet. What’s the best way to secure the safe?
Thanks in advance.
If the cabinets in the kitchen are new and have never had knobs installed in them before you will have to first measure and mark off where the cabinet knobs will go before drilling any holes. First, decide where the knobs will look the best on the cabinet. Some people prefer the center of the cabinet edge for the knobs while others prefer something that is off center. 3 inches above the bottom of an upper cabinet is generally a good place for kitchen cabinet knobs to be installed. Using a ruler and a pencil, make a small mark on the cabinet where the hole will be drilled for the knob. Make sure all of the cabinets have equal and accurate measurements so all of the knobs are equally placed and spaced. If upper cabinet knobs are placed 3 inches from the bottom of the cabinet, place the knobs 3 inches from the top of lower cabinets below the counter top.
Most kitchen cabinet knobs are attached to a screw or a cylindrical attachment that goes through the hole drilled in the cabinet. Before drilling any holes, inspect the size of the screw that is to go through the cabinetry and pick a drill bit of a coordinating size to drill the hole with. Following the marked off measurements previously made, drill a hole for each knob on the cabinet. Once the hole is made, the cabinet knob can be put through the hole and secured at the back.
If there are already knobs in the kitchen cabinet and you wish to replace the old ones with new ones the process is quite simple. Drilling is rarely needed because they can usually be unscrewed by hand or easily taken off with the help of a hand held screw driver. Once the old knobs are unscrewed and taken out, the new ones can be installed by putting them through the holes that the previous ones were in and securing them in the back.
It replaces the vent hood. My hood is not vented but it wont matter. How difficult is it? Ive got tools and a drill and such.
I am renting my apartment, and I bought an under the cabinet radio for my kitchen and didn’t think about it until I got home, that I’m renting and I’m not sure if I can put the holes under the cabinet!
Has anyone done this? I’m not sure if there’s an easy way to fill the holes, or if there’s another way I can attach the radio?
BLOCKS. OKAY. THAT SHOULD WORK. NOW WE HAVE AN OPENING FOR OUR REFRIGERATOR. THE LAST FEW MINUTES, I’VE BEEN PREPARING THE CABINET THAT’S GOING TO BE ON THE WALL NEXT TO THE REFRIGERATOR. I’VE DRILLED A HOLE FOR THE POWER LINE TO THE UNDER CABINET LIGHT. I’VE PRE-DRILLED THE HOLES FOR THE SCREWS THAT ARE GOING TO HOLD THE CABINET TO THE WALL. AND I’VE SET THESE PROPS IN PLACE TO HOLD THE CABINET AT THE RIGHT HEIGHT WHILE I SCRIBE THIS END, AS WELL AS WHILE I INSTALL THE SCREWS. NOW, WHO’S …
BLOCKS. OKAY. THAT SHOULD WORK. NOW WE HAVE AN OPENING FOR OUR REFRIGERATOR. THE LAST FEW MINUTES, I’VE BEEN PREPARING THE CABINET THAT’S GOING TO BE ON THE WALL NEXT TO THE REFRIGERATOR. I’VE DRILLED A HOLE FOR THE POWER LINE TO THE UNDER CABINET LIGHT. I’VE PRE-DRILLED THE HOLES FOR THE SCREWS THAT ARE GOING TO HOLD THE CABINET TO THE WALL. AND I’VE SET THESE PROPS IN PLACE TO HOLD THE CABINET AT THE RIGHT HEIGHT WHILE I SCRIBE THIS END, AS WELL AS WHILE I INSTALL THE SCREWS. NOW, WHO’S …